Fault Code 73: Failed to Engage Gear
J1587: MID 130SID 58FMI 7
J1939: SA 3SPN 781FMI 7
Overview
The Fuller Advantage transmission uses the X-Y Shifter to engage and disengage a gear based on the driver’s selected mode of operation. Gear engagement is achieved by activating the X-Y Shifter Gear Motor, which controls the fore-and-aft movement of the Shift Finger. Pushing the Shift Finger against one of the Shift Bar Housing Shift Blocks guides the Shift Yoke to engage the Sliding Clutch into a gear. The position of the X-Y Shift Finger is monitored by the Transmission Electronic Control Unit (TECU) by way of the X-Y Gear Position and Rail Position Sensors. Fault Code 73 is set when the X-Y Shift Finger attempts to engage a gear, but the X-Y Gear Position Sensor indicates that the transmission was unable to engage that gear. The TECU detected a system failure, but was unable to detect the specific root cause.
This fault can only be detected when there are no failures of the TECU, X-Y Gear or Rail Motors, X-Y Position Sensors or Battery Supply voltage. This fault code is set when the system is unable to engage a gear.Detection
Conditions to Set Fault Code Active
FMI 7 – Mechanical System Not Responding: If the X-Y Gear Position Sensor does not meet the minimum gear engagement value after five consecutive attempts to engage the desired gear, this fault code sets Active.
FMI 7Fallback
Conditions to Set Fault Code Inactive
FMI 7: The system successfully engages the desired gear.
Possible Causes
FMI 7
1. Transmission Electronic Control Unit (TECU) 2. 38-Way Transmission Harness Connector 3. Gear Position Sensor 4. 3-Way Gear Position Sensor Connector 5. 2-Way Gear Motor Connector (blue) 6. 2-Way Gear Motor Connector Body (blue) 1. X-Y Shifter 2. 2-Way Rail Motor Connector (black) 3. 2-Way Rail Motor Connector Body (black) 4. 3-Way Rail Position Sensor Connector 5. Rail Position Sensor 6. 38-Way Vehicle Harness ConnectorComponent Identification
Fault Code 73 Troubleshooting
A Purpose:Check for Active or Inactive fault codes. Set parking brake and chock wheels. Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. Note: If Fault Code 73 is Inactive and there are other Active fault codes, troubleshoot all Active fault codes first. If Fault Codes 33, 34, 51, 52, 61, 63 or 64 are Active or Inactive, troubleshoot per Fault Code Isolation Procedure. If Fault Code 73 FMI 7 is Active or Inactive and the Input Shaft was recently installed or replaced, go to TAIB-0999 Fault Code 73 FMI 7 After Recent Input Shaft Replacement. If Fault Code 73 FMI 7 is Active or Inactive, and the Input Shaft was not recently installed or replaced, Go to Step B B Purpose:Verify TECU Software Version. Key on with engine off. Connect ServiceRanger. Go To Programming. Under "Software Information", record TECU software version. If TECU software is less than 5570059, update TECU software to 5570059 or greater. Go to Step C If TECU software is 5570059 or greater, Go to Step C C Purpose:Determine Vehicle Engine Manufacturer. Determine if vehicle Engine manufacturer is PACCAR. If vehicle Engine is not manufactured by PACCAR, Go to Step D If vehicle Engine is manufactured by PACCAR, Go to Step E D Purpose:Verify Engine Calibration Configuration Setting. Key on. Connect ServiceRanger. Go To Configuration. Select Engine. Record Engine Calibration Current Value. If the Current Value indicates “Advantage Gear Engagement 5573534”, Go to Step G If the Current Value does not indicate “Advantage Gear Engagement 5573534”, from the "New Value" drop down select “Advantage Gear Engagement 5573534” and follow on-screen prompts. Go to Step V E Purpose:Verify Engine Calibration Configuration Setting. Key on. Connect ServiceRanger. Go To Configuration. Select Engine. Record Engine Calibration Current Value. If the Current Value indicates “PACCAR MX11/MX13 Powertrain Optimized 5573562”, Go to Step G If the Current Value does not indicate “PACCAR MX11/MX13 Powertrain Optimized 5573562”, from the "New Value" drop down select “PACCAR MX11/MX13 Powertrain Optimized 5573562” and follow on-screen prompts. Go to Step V F Purpose:Verify Completed Processes Note what actions were taken in previous steps. If TECU software version and/or the Engine Calibration value were updated per previous steps, Go to Step V If TECU software version and/or the Engine Calibration value did not require an update during previous steps, Go to Step G G Purpose:Use Product Diagnostic (PD) Mode to locate intermittent failures. Set parking brake and chock wheels. Place transmission in PD Mode. See more about Product Diagnostic (PD) Mode. Note: Fault Code 73 does not set Active during PD Mode. Other fault codes may set Active during PD Mode that could indicate an issue with the wiring. Note: Transmission does not enter PD Mode when Active fault codes exist. Wiggle wiring and connections of the Transmission Harness from the X-Y Shifter to the TECU. Wiggle wiring and connections of the Vehicle Power Supply Harness from the batteries to the TECU. Exit PD Mode by powering down. Notice Allow 2–3 minutes for the TECU to perform a complete power-down sequence before proceeding. If any fault sets Active while wiggling the Transmission Harness, replace Transmission Harness. Go to Step V If any fault sets Active while wiggling the Power Supply Harness, refer to OEM guidelines for repair or replacement of Power Supply wiring. Go to Step V If no fault codes set Active, Go to Step H H Purpose:Inspect the batteries, in-line fuse and power and ground supplies to the TECU. Key off. Notice Allow 2–3 minutes for the TECU to perform a complete power-down sequence before proceeding. Inspect Starter, battery terminals and transmission 30-amp In-line Fuse Holder Connections for corrosion, loose terminals and bent or spread pins. Inspect Battery Positive (+) and Negative (-) wires from the batteries to the TECU including all connections. Ensure a clean ground connection on the chassis. Verify no damage or corrosion to connectors. If damage is found, repair or replace Power Supply Harness per OEM guidelines. Go to Step V If no damage is found, Go to Step I I Purpose:Perform a Load Test on each vehicle battery. Key off. Set parking brake and chock wheels. Load test each vehicle battery per OEM specifications. Record reading(s). If any battery(s) does not pass the Load Test, refer to OEM guidelines for repair or replacement of battery(s). Go to Step V If all batteries pass the Load Test, Go to Step J J Purpose:Inspect X-Y Shifter and Transmission Harness for physical damage. Key off. Notice Allow 2–3 minutes for the TECU to perform a complete power-down sequence before proceeding. Inspect the physical condition of X-Y Shifter and all connections. Inspect Transmission Harness for any pinched, chafed, corroded or shorted wiring. Disconnect both 2-Way X-Y Gear and Rail Position Sensor Connectors. Disconnect both 2-Way X-Y Motor Connectors to the Transmission Harness. Inspect connectors for corrosion, loose terminals, bent or spread pin or damage to the connector bodies. If damage to the X-Y Shifter or X-Y Shifter wiring is found, replace X-Y Shifter. Go to Step V If damage to the Transmission Harness is found, replace Transmission Harness. Go to Step V If no damage is found, Go to Step K K Purpose:Inspect condition of X-Y Shifter internal components. Key off. Remove the X-Y Shifter. Inspect condition of the X-Y Shift Finger and Cross Shaft for damage or wear. If damage to the X-Y Shifter is found, replace X-Y Shifter. Go to Step V If no damage is found, Go to Step L L Purpose:Inspect Condition of Shift Bar Housing. Key off. Inspect condition of the Shift Bar Housing Shift Blocks. Look for uneven gaps between the Shift Blocks or excessive wear to the block faces. Verify Shift Blocks are tight to the rails and there are no other mechanical issues with the Shift Bar Housing. Verify transmission shifts fully in and out of each gear. Test the Shift Interlock to verify that the transmission will not engage two gears at once. See the Shift Interlock Inspection Procedure Shift Interlock Inspection. If damage to the Shift Bar Housing is found, repair Shift Bar Housing. Go to Step V If no damage is found, Go to Step M M Purpose:Inspect condition of the internal transmission components. Key off. Drain and save the transmission oil. Inspect oil for significant metal fragments. Remove 8-bolt PTO cover. Inspect main case gears for damage or excessive movement. Inspect Shift Yokes and Sliding Clutches for damage or excessive wear. If damage is found or there are significant metal fragments in the oil, replace damaged, worn or failed transmission components. Go to Step V If no damage is found within the transmission main case, replace X-Y Shifter and Transmission Harness. Go to Step V Note: If unsure whether damage or wear is significant, take pictures of the transmission gearing. Ensure these pictures are clear and the components are easily visible. Email these pictures to auto.rtw@eaton.com and contact Eaton at (800) 826-4357. V Purpose:Verify repair. Key off. Reconnect all connectors and verify that all components are properly installed, including X-Y Shifter. Reinstall 8-bolt PTO cover. Refill transmission with lubricant. Key on with engine off. Clear fault codes using ServiceRanger. Drive vehicle and attempt to reset the code or duplicate the previous complaint. Check for fault codes using ServiceRanger. If no fault codes set Active and vehicle operates properly, test complete. If a fault code other than 73 sets Active, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 73 sets Active, contact Eaton at (800) 826-4357 for further diagnostics.
Battery Voltage Drop Load Test Status (Pass/Fail) 1 2 3 4 5 
